WD30EZRX - Fehler im S.M.A.R.T. Error Log

Makrolon

Banned
Thread Starter
Mitglied seit
08.10.2005
Beiträge
826
Hallo,

kann mir hier jemand im Festplatten-Forum, 4 Fehler im S.M.A.R.T. Error Log meiner neuen WD30EZRX erklären bzw. was diese bedeuten?

smartctl 5.41 2011-06-09 r3365 [i686-w64-mingw32-win7(64)-sp1] (sf-win32-5.41-1)
Copyright (C) 2002-11 by Bruce Allen

=== START OF INFORMATION SECTION ===
Device Model: WDC WD30EZRX-00MMMB0
Serial Number: WD-************
LU WWN Device Id: 5 0014ee 0585cba3d
Firmware Version: 80.00A80
User Capacity: 3.000.592.982.016 bytes [3,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Feb 19 23:03:49 2012 MZ
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (51480) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 202 170 021 Pre-fail Always - 6858
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 21
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 7
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 12
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 10
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 33
194 Temperature_Celsius 0x0022 125 121 000 Old_age Always - 27
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0

SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 4 occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 30 4f c2 e0 Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d6 01 be 4f c2 e0 00 00:07:54.275 SMART WRITE LOG
b0 da 01 00 4f c2 e0 00 00:07:54.212 SMART RETURN STATUS
80 44 00 00 44 57 e0 00 00:07:54.212 [VENDOR SPECIFIC]
b0 d6 01 be 4f c2 e0 00 00:07:54.182 SMART WRITE LOG
80 45 00 00 44 57 e0 00 00:07:54.182 [VENDOR SPECIFIC]

Error 3 occurred at disk power-on lifetime: 2 hours (0 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 30 4f c2 a0 Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d6 01 be 4f c2 a0 00 00:04:37.982 SMART WRITE LOG
b0 da 01 00 4f c2 a0 00 00:04:37.918 SMART RETURN STATUS
80 44 00 00 44 57 a0 00 00:04:37.918 [VENDOR SPECIFIC]
b0 d6 01 be 4f c2 a0 00 00:04:37.884 SMART WRITE LOG
80 45 00 01 44 57 a0 00 00:04:37.884 [VENDOR SPECIFIC]

Error 2 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 30 4f c2 e0 Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d6 01 be 4f c2 e0 00 00:09:37.235 SMART WRITE LOG
b0 da 01 00 4f c2 e0 00 00:09:37.172 SMART RETURN STATUS
80 44 00 00 44 57 e0 00 00:09:37.172 [VENDOR SPECIFIC]
b0 d6 01 be 4f c2 e0 00 00:09:36.709 SMART WRITE LOG
80 45 00 00 44 57 e0 00 00:09:36.709 [VENDOR SPECIFIC]

Error 1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 01 30 4f c2 a0 Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 d6 01 be 4f c2 a0 00 00:06:20.542 SMART WRITE LOG
b0 da 01 00 4f c2 a0 00 00:06:20.479 SMART RETURN STATUS
80 44 00 00 44 57 a0 00 00:06:20.479 [VENDOR SPECIFIC]
b0 d6 01 be 4f c2 a0 00 00:06:20.444 SMART WRITE LOG
80 45 00 01 44 57 a0 00 00:06:20.444 [VENDOR SPECIFIC]

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed without error 00% 2 -
# 2 Conveyance offline Completed without error 00% 0 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Danke!
 
Wenn Du diese Anzeige nicht sehen willst, registriere Dich und/oder logge Dich ein.
Ignorier die Fehler. Es wurde wohl versucht einen Status von der HDD abzufragen den diese nicht unterstützt. Wichtig für dich sind:
SMART overall-health self-assessment test result: PASSED
sowie
# 1 Conveyance offline Completed without error 00% 2 -
# 2 Conveyance offline Completed without error 00% 0 -
Und vielleicht auch die Herstellerempfehlung respektieren:
Extended self-test routine
recommended polling time: ( 255) minutes.
Öfters sollte man die HDD nicht abfragen für einen langen Selbsttest.
 
Hardwareluxx setzt keine externen Werbe- und Tracking-Cookies ein. Auf unserer Webseite finden Sie nur noch Cookies nach berechtigtem Interesse (Art. 6 Abs. 1 Satz 1 lit. f DSGVO) oder eigene funktionelle Cookies. Durch die Nutzung unserer Webseite erklären Sie sich damit einverstanden, dass wir diese Cookies setzen. Mehr Informationen und Möglichkeiten zur Einstellung unserer Cookies finden Sie in unserer Datenschutzerklärung.


Zurück
Oben Unten refresh