Habe das default genommen: http://www.hs-augsburg.de/~ingmar_k/Pogoplug_V3/kernels/2.6.32-ppv3-classic-zram-1.1_ARMv6k.tar.bz2
Da ist die /lib/firmware/gmac_copro_firmware mit drin...
Da ist die /lib/firmware/gmac_copro_firmware mit drin...
root@pogoplug:~# lsmod
Module Size Used by
zram 9948 2
gmac 35472 0
mii 4300 1 gmac
Jan 1 00:00:20 pogoplug kernel: [ 13.980000] hw_set_mac_address() Storing port0 mac_adr in global array
Jan 1 00:00:20 pogoplug kernel: [ 13.980000] CoPro offload is active on eth0
Jan 1 00:00:20 pogoplug kernel: [ 13.990000] Alloc'ing ARM descs 8192 bytes
Jan 1 00:00:20 pogoplug kernel: [ 13.990000] Alloc'ing CoPro parameters 40 bytes
Jan 1 00:00:20 pogoplug kernel: [ 14.000000] gmac gmac.0: firmware: requesting gmac_copro_firmware
Jan 1 00:00:20 pogoplug kernel: [ 14.030000] CoPro: Programming start address as 0xd000e000
Jan 1 00:00:20 pogoplug kernel: [ 14.130000] eth0: Resetting GMAC
Jan 1 00:00:20 pogoplug kernel: [ 14.140000] eth0: GMAC reset complete
Jan 1 00:00:20 pogoplug kernel: [ 14.140000] workaround step1
Jan 1 00:00:20 pogoplug kernel: [ 14.140000] workaround step2
Jan 1 00:00:20 pogoplug kernel: [ 14.150000] workaround finish
Jan 1 00:00:20 pogoplug kernel: [ 14.150000] hw_set_mac_address() Storing port0 mac_adr in global array
Jan 1 00:00:20 pogoplug kernel: [ 14.160000] eth0: Setting Rx flow control thresholds for LAN port
Jan 1 00:00:20 pogoplug kernel: [ 14.160000] CoPro available SRAM end 0x00000001
Jan 1 00:00:20 pogoplug kernel: [ 14.170000] Copro offload started
Jan 1 00:00:20 pogoplug kernel: [ 14.170000] Waiting for auto-negotiation to complete
Jan 1 00:00:20 pogoplug kernel: [ 14.680000] Waiting for auto-negotiation to complete
Jan 1 00:00:20 pogoplug kernel: [ 14.680000] eth0: PHY is Realtek RTL8211D, type 0x001cc914
Jan 1 00:00:20 pogoplug kernel: [ 14.690000] eth0: Disable EEE (Energy Efficient Ethernet 802.3az)
Jan 1 00:00:20 pogoplug kernel: [ 14.690000] eth0: Set SSC
Jan 1 00:00:20 pogoplug kernel: [ 15.200000] eth0: link down
Jan 1 00:00:20 pogoplug kernel: [ 17.190000] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 1 00:00:20 pogoplug kernel: [ 17.200000] eth0: link up, 100Mbps, full-duplex, using pause, lpa 0x45E1
Jan 1 00:00:20 pogoplug kernel: [ 17.230000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 755.800000] usb 1-1.3: new full speed USB device using oxnas-ehci and address 5
[ 755.880000] usb 1-1.3: device descriptor read/64, error -32
[ 756.070000] usb 1-1.3: device descriptor read/64, error -32
[ 756.260000] usb 1-1.3: new full speed USB device using oxnas-ehci and address 6
[ 756.340000] usb 1-1.3: device descriptor read/64, error -32
[ 756.530000] usb 1-1.3: device descriptor read/64, error -32
[ 756.720000] usb 1-1.3: new full speed USB device using oxnas-ehci and address 7
[ 757.140000] usb 1-1.3: device not accepting address 7, error -32
[ 757.220000] usb 1-1.3: new full speed USB device using oxnas-ehci and address 8
[ 757.640000] usb 1-1.3: device not accepting address 8, error -32
[ 757.640000] hub 1-1:1.0: unable to enumerate USB device on port 3
Das kommt drauf an was du unter billig verstehst und was für Ansprüche du hast.