Suchergebnisse

Hmmm...maybe? But was using windowed just to keep hwinfo so i can see it when messing around with voltages....i coukd have sworn i had used windowed in the past to do just that and fps wasnt capped

Hey all! Was that testing done with changing duty gain etc?

Hey guys...might you know why when i try running time spy in window mode the fps is capped at 60hz? Im not running adrenaline..just driver....when i run full screen i get the correct fps for the oc'ing im doing

Ok all im gonna give it a run with the evc...now i think i know why i should use it...i cant see more than 1.35v using software...with the evc i can go higher than that no?...only testing at the moment... Just one thing though...when i click find devices in the evc software i just get...

Well the hylomar did the trick....no leaks!! So hopefully a few more runs this week

Had to put a stop to these shenanigans for now...the leak seems to be getting worse...and i wish to push the temps to the limit....ive pulled the card out and removed the face of the waterblock..im thinking a small bead of hylomar next to the o ring...all the way around may be just what is...

https://www.3dmark.com/spy/56488030 Grabbed another spot....gonna try 24.10.1 driver ozver the weekend

Ok got a few more runs in today..i just tried tightening the screws a bit more and packed around/under the gpu with towel... Cracked the top 10 but only just...i can see you guys up ahead of me....will keep trying! 27603-1.337v -15°C coolant temperature Upped voltage bit by bit..kept raising...

Yeah...i could always just pack shop towel around it for runs 😆😆 aint that bad a leak..but bwing in that chillbox there is zero insulation done...but a permanent solution would be the best 😀

Also!...the xfx speedster zero uses an EK block..no leaks at all until i reach around -10c then it develops a small drip...ive tried tightening the nuts that hold it to the card but no joy...so the o ring is failing at those temps? Or could the plexi be warping?...its only in one spot...i was...

https://www.3dmark.com/spy/56434452 This the best so far.....pretty much maxxed the clocks....so gonna have to look elsewhere... More MPT meddling 😆😆 Thats 1.325v....so if anything will push a few more mv through it and see if i can get a bit higher core clock Will post up mpt/mct settings...

Ok...gave it a redo with LM....also used a putty instead of pads...i had no 1.25mm to change from 1.5mm...i think i just needed a bit better contact...and yep dropped 10c off hotspot...30c delta at 550w... Also managed to get my best graphics score! 27358....i have uploaded to futuremark but i...

Yes i have some dessicants in there...Activated alumina

Devcom was using same model wonder what his temps are like

Lol..of course!

Haha yes so true!!

Yeah i was thinking so myself...oh well time to drain the loop again 😆😆 1748176038 Is just a modified air conditioner....to run below 0c....pumping ethalyne glycol with a strong submersible pond pump.... Temps controlled with inkbird... pc is in a beer cooler...everything inside except the...

Dnt really wanna pull the card out again 🙄 😆 1748168360 This is the set up now..in a chill box..no condensation to worry about! This last run was at 1.32v

OK, that's around 550w... conductonaut extreme.... Tried with normal thermal paste temps were worse

Hey all long time no see!! Just a quick question...recently have had more time to muck around with my set up... Coolant temperature -15°C around 1.35v pretty much maxxed out MPT settings...what should my gpu delta be in regards to coolant temp? GPU sits around 27c on time spy..hotspot around...